®rostat Operator I

Job Summary This position is located OCONUS within the CENTCOM Area of Operation. Aerostat Operators provide Operations and Sustainment (O&S) support for the Persistent Surveillance Systems – Tethered (PSS-T) program in OCONUS site locations. PSS-T is comprised of former Persistent Ground Surveillance System (PGSS) and Persistent Threat Detection System (PTDS) programs. Primary areas of responsibility are dependent on the position held: Aerostat Operators/User-level maintainers will participate in the overall, hands-on operation of the aerostat system including launch, in-flight, recovery, and moored activities. Candidates will perform all functions to operate the PGSS/PTDS, an aerostat mounted Intelligence, Surveillance, And Reconnaissance (ISR) platform, its Mobile Mooring Platform (MMP), Sensor Payload(s), communications and navigation systems as well as associated support equipment (Boom Lift, Forklift, All Terrain Vehicles (ATV's), and Electrical Power Generators). Candidate will perform User-level maintenance functions include performing hands-on Preventative Maintenance Checks and Services (PMCS), troubleshooting, removing and replacing Line Replaceable Units (LRUs), and removing and replacing payloads. Candidate must possess a diverse range of skills with the ability to quickly adapt to new situations. Tasks will be performed under direction of higher classified technicians and/or site personnel. Additional responsibilities include performing analyses of system operations and candidates must have: Knowledge of and experience in the operations of hardware systems and components. Experience in fault detection, isolation, and correction of hardware systems and individual components. Ability to perform routine system maintenance and analysis functions including hardware configurations; adding, removing and replacing hardware components; use of hardware and software diagnostic testing tools; reading of electronic circuit schematics; and repairing printed circuit boards. Minimum Requirements Basic Qualifications (all): A high school diploma or equivalent is required. A two-year associate degree in a technical field from an accredited college can substitute for work experience. At least ONE (1) year previous Aerostat experience Candidate must be a U.S. Citizen and possess a Current or active DoD Secret clearance. Preferred candidates with active US passport. Two years of experience in one of the following areas may be substituted in lieu of aerostat experience: Electrical Maintenance Mechanic Possess at least two (2) year’s aerostat experience as an operator at the 20 series level or greater from Army MOS 35F (Intelligence Analyst), 35G (Geospatial Intelligence Imagery Analyst), 35H (Common Ground System Analyst), 96R (Ground Surveillance Systems Operator), 96U (Unmanned Aerial Vehicle Operator), or military branch equivalent. Two years of hands-on experience in performing operations and maintenance tasks either on an AEROSTAT system or a related industry/military equivalent is required. Must be qualified at the 10 series or greater level (via military or civilian technical schools) is required. Ability to read electronic schematics. O&M of electro-mechanical equipment to include one or more of the following: Hydraulic/servo valves Hydraulic actuators, control systems Test and diagnostic equipment Networking, IT & information systems Two years’ experience is required. Must be qualified at the 10 series or greater level; MOS 25B/F or other military branch equivalent or industry occupational specialties as a CISCO Network Administrator; Army MOS 25L/N or other military branch equivalent or industry occupational specialties as a Network Installation (BICSI or Network + or Comp T Certification) will be considered. CCIE certification with fiber optic certification is preferred. Mechanical Maintenance Mechanical Maintenance with qualifications at the 10 series or greater from U.S. Army MOS 94D/X and 91/B/S/W or other military branch equivalent, or industry occupational specialties such National Institute for Automotive Service Excellence (ASE) Certified Truck Mechanic or Federal Aviation Administration (FAA) General Mechanic 1 or greater. Two years of hands-on experience on an AEROSTAT system or a related industry/military equivalent is required. O&M of mechanical equipment to include one or more of the following: Hydraulic systems Winch systems Tether/cable handling systems Industrial generator sets Power switch gear HVAC CranesAerial lift Forklift Industrial generator sets Work Environment, Physical Demands and Mental Demands: Ability to perform job duties efficiently and effectively. Must be able to lift up to 50 lbs. Must be able to work in extreme environmental conditions including dust and high temperatures. Must be able to endure long hours, exposure to weather and hazardous conditions. Other Responsibilities: Safety - AMENTUM enforces a safety culture whereby all employees have the responsibility for continuously developing and maintaining a safe work environment. As appropriate, each employee is responsible for completing all training requirements and fulfilling all self-aid/buddy aid responsibilities, participating in emergency response tasks and serving on safety committees and teams. Quality - Quality is the foundation for the management of our business and the keystone to our goal of customer satisfaction. It is our policy to consistently provide services that meet customer expectations. Accordingly, each employee must conform to the AMENTUM Quality Policy and carry out job activities in compliance with applicable AMENTUM Quality System documents and customer contracts. Each employee must read and understand his/her Quality Management and Customer Satisfaction responsibilities. Procedure Compliance - Each employee must read, understand and implement the general and specific operational, safety, quality and environmental requirements of all plans, procedures and policies pertaining to his/her job. Disclaimer: This position description indicates the general nature and level of work expected. It is not designed to cover or contain a comprehensive listing of activities, duties or responsibilities required. Employee may be asked to perform other duties as required.